$$\newcommand{\bra}[1]{\left<#1\right|}\newcommand{\ket}[1]{\left|#1\right>}\newcommand{\bk}[2]{\left<#1\middle|#2\right>}\newcommand{\bke}[3]{\left<#1\middle|#2\middle|#3\right>}$$
X
INFORMAÇÕES SOBRE DIREITOS AUTORAIS


As obras disponibilizadas nesta Biblioteca Digital foram publicadas sob expressa autorização dos respectivos autores, em conformidade com a Lei 9610/98.

A consulta aos textos, permitida por seus respectivos autores, é livre, bem como a impressão de trechos ou de um exemplar completo exclusivamente para uso próprio. Não são permitidas a impressão e a reprodução de obras completas com qualquer outra finalidade que não o uso próprio de quem imprime.

A reprodução de pequenos trechos, na forma de citações em trabalhos de terceiros que não o próprio autor do texto consultado,é permitida, na medida justificada para a compreeensão da citação e mediante a informação, junto à citação, do nome do autor do texto original, bem como da fonte da pesquisa.

A violação de direitos autorais é passível de sanções civis e penais.
Coleção Digital

Avançada


Estatísticas | Formato DC |



Título: HIGH-DENSITY POLYETHYLENE COMPOSITES REINFORCED WITH IN2W3O12 NANOPARTICLES
Autor: GUSTAVO SCHINAZI
Instituição: PONTIFÍCIA UNIVERSIDADE CATÓLICA DO RIO DE JANEIRO - PUC-RIO
Colaborador(es):  JOSE ROBERTO MORAES D ALMEIDA - ADVISOR
BOJAN MARINKOVIC - CO-ADVISOR

Nº do Conteudo: 29717
Catalogação:  20/04/2017 Idioma(s):  PORTUGUESE - BRAZIL
Tipo:  TEXT Subtipo:  THESIS
Natureza:  SCHOLARLY PUBLICATION
Nota:  Todos os dados constantes dos documentos são de inteira responsabilidade de seus autores. Os dados utilizados nas descrições dos documentos estão em conformidade com os sistemas da administração da PUC-Rio.
Referência [pt]:  https://www.maxwell.vrac.puc-rio.br/colecao.php?strSecao=resultado&nrSeq=29717@1
Referência [en]:  https://www.maxwell.vrac.puc-rio.br/colecao.php?strSecao=resultado&nrSeq=29717@2
Referência DOI:  https://doi.org/10.17771/PUCRio.acad.29717

Resumo:
High-density polyethylene (HDPE) is one of the most widely used materials. Despite its numerous qualities, such as low density, high ductility, and high specific strength, HDPE presents certain disadvantages that limit its applicability, like low stiffness, low thermal stability, and high thermal expansion. In contrast, there is a select group of materials that display negative or near-zero coefficient of thermal expansion (CTE). Ceramics belonging to the A2M3O12 family, which includes In2W3O12 (indium tungstate), are examples of such materials. Therefore, this dissertation proposes to examine different methods of physical mixture in order to produce and characterize HDPE composites reinforced with In2W3O12 nanoparticles with reduced CTE and better mechanical properties than the neat polymer. Firstly, In2W3O12 nanoparticles were synthesized by coprecipitation. Simultaneous thermal analysis proved their crystallization temperature and monoclinic/orthorhombic phase transition temperature to be approximately 530 Celsius degrees and 259 Celsius degrees, respectively. The lattice parameters at room temperature were determined by XRD, and the intrinsic CTE s for both phases were calculated by variable-temperature in situ XRD. For the first time, a negative intrinsic CTE was found for the orthorhombic phase (Alpha 1 equal than minus 1.5 multiplied 10 power minus 6 and K power minus 1). Secondly, composites were produced from HDPE pellets and the In2W3O12 nanoparticles by microextrusion and microinjection preceded by a pre-mixing step. Two fabrication parameters were analyzed: the filler content (0.5, 2, 4, and 10wt percent were used) and the pre-mixing method (no pre-mixture, by vibration within a mill without balls, and in a rotating autoclave at 190 Celsius degrees and ambient pressure). Finally, the composites were characterized by tensile tests, dilatometry, and thermogravimetric analysis. All of the composites presented higher Young s modulus and yield stress than neat HDPE, with increases of up to 45 percent and 17 percent, respectively. The best results were displayed by the materials that were pre-mixed in the mill with 10wt percent filler fraction. In general, both pre-mixing methods improved the composites mechanical properties. On the other hand, the polymer s CTE was not significantly reduced, being decreased by 6 percent in the best case. The degradation temperature showed almost no improvement, with a 1.5 percent increase for the composites with 0.5 percent filler content. Lastly, neat HDPE samples exposed to the different pre-mixing methods were analyzed by differential scanning calorimetry and compared with the as-received pellets. Results showed that the melting temperature was not affected by the mixing techniques, but both the enthalpy of fusion and the degree of crystallinity were increased by 8 percent and 15 percent for the samples pre-mixed by vibration in the mill and by rotation in the autoclave, respectively.

Descrição Arquivo
COMPLETE  PDF
Logo maxwell Agora você pode usar seu login do SAU no Maxwell!!
Fechar Janela



* Esqueceu a senha:
Senha SAU, clique aqui
Senha Maxwell, clique aqui